Makita 5007Mg Circular Saw Review: Worth It? (November 2026)
The Makita 5007Mg suits framing and panel work if you want a corded 7-1/4 in saw with magnesium components, two cut-line lights and bevel stops. Choose the lighter DeWalt DWE575SB if lower weight matters more.
On this page (6 sections)
The Makita 5007Mg Circular Saw suits framing and panel work, with magnesium components, a 15 amp motor and two built-in cut-line LEDs. Its 2-1/2 in cut capacity at 90° and bevel range up to 56° cover straight and angled cuts.
Its trade-off is weight: it weighs 10.6 lb, compared with 8.8 lb for the DeWalt DWE575SB. Choose the Makita for its magnesium components, LEDs and included accessories, or compare the DeWalt DWE575SB and Makita 5007Mg if weight is a deciding factor.
What does the Makita 5007Mg offer?
The Makita 5007Mg combines magnesium components, a 15 amp motor and two cut-line LEDs in a corded saw. It comes with a 7-1/4 in 24-tooth framing blade, case, hex wrench and rip fence.
Makita 5007Mg Circular Saw: Best for framing and panel work
- Magnesium components
- 15 amp motor
- 2-1/2 in cut at 90°
- Two cut-line LED lights
A corded 7-1/4 in saw with magnesium components, two built-in LEDs and a 0° to 56° bevel range. Its cutting capacity suits dimensional and engineered lumber as well as sheet goods.
Pros
- Magnesium components
- Two built-in cut-line LEDs
- Positive bevel stops at 22.5° and 45°
- Includes a case and rip fence
Cons
- 10.6 lb weight is higher than the DWE575SB
- Bevel range tops out at 56°
Makita designed the saw for framing walls, floors and roofs, cutting dimensional and engineered lumber, and ripping panels such as plywood and OSB. Its 2-1/2 in capacity at 90° and 0° to 56° bevel range give you specific limits to check against your work.
The two LEDs illuminate the cut line, and the saw also has a built-in dust blower. These features help keep the cut path visible, but they don't replace a clear layout mark or proper support for the workpiece.
How does the Makita 5007Mg compare with the 5007F?
The 5007Mg has a wider bevel range than the Makita 5007F: up to 56° compared with 45°. The 5007F has a 2-3/8 in cut capacity at 90° and 1-3/4 in at 45°.
Both saws have a 15 amp motor, two built-in LEDs and a dust blower. The 5007F also has an AC/DC switch and all-ball-bearing construction, while the 5007Mg uses magnesium components.
The Makita 5007F Circular Saw is an alternative if its common-angle range fits your work. Compare cutting depths and bevel needs before choosing between the two.
Is the Makita 5007Mg easy to handle?
The 5007Mg weighs 10.6 lb, making it heavier than the DeWalt and Skil alternatives here. Makita describes its magnesium construction as lightweight and balanced, but consider that weight if you regularly carry the saw between cuts.
For a lighter option, the DeWalt DWE575SB weighs 8.8 lb and has a 57° bevel capacity. The Skil 5280-01 weighs 8.7 lb and adds a single-beam laser guide; see our best corded circular saws to compare more options.
Handling also depends on the setup. Support boards and panels as the manual directs, keep your hands clear of the blade, and let the saw reach full speed before starting the cut.
What cuts can the Makita 5007Mg make?
The 5007Mg is designed for straight, bevel and plunge cuts in lumber and sheet goods. Its cut capacity at 90° is 2-1/2 in, and its bevel capacity runs from 0° to 56° with positive stops at 22.5° and 45°.
Use the 45° stop for common bevel work, and check the setting before cutting at other angles. Beveling reduces the cutting depth, so confirm that the setting works for the board or panel.
For long straight cuts, mark the cut and support the material as the manual directs to reduce blade pinching and kickback risk. Our guide to cutting straight with a circular saw covers setup and guide options.
Is the included blade suitable for your work?
The saw includes a 7-1/4 in, 24-tooth Makita framing blade for framing tasks. For other work, choose a compatible blade rated for the material, saw speed and finish you need.
The blade is a replaceable part, so you can choose a suitable blade for a specific task. Follow the manual for blade compatibility, installation and safe handling, and disconnect power before making a change.
If you need a refresher, our guide on how to change a circular saw blade explains the basic steps. Check blade direction and follow the manual's tightening instructions before reconnecting power.
What should you know about visibility and dust?
The 5007Mg has two LEDs and a built-in dust blower to help keep the cut line visible. The blower moves sawdust away from the line, but it doesn't collect dust or make it safe to breathe.
Set up your cut in a well-lit area and mark the line clearly. Follow the saw manual and material guidance for dust control, eye protection and any required respiratory protection.
A visible cut line helps only when the saw stays aligned. Keep the base flat against the work and use a suitable guide when a long, straight edge matters.
Is the Makita 5007Mg the right saw for you?
Choose the 5007Mg if you want a corded saw with a 56° bevel range, cut-line LEDs and a case and rip fence included. Its 15 amp motor and 2-1/2 in cutting depth at 90° suit framing and panel tasks within those limits.
Look elsewhere if lower weight is your top priority. The DeWalt DWE575SB and Skil 5280-01 are lighter alternatives, while the Makita 5007F has a narrower 45° bevel range and similar cut-line lighting.
For a broader decision, our circular saw versus track saw guide explains when a handheld saw or a track-based setup fits the job better. Choose based on the materials, angles and cut length you handle most.
What score does the Makita 5007Mg receive?
The Makita 5007Mg scores 8.3 out of 10 for its combination of a 15 amp motor, magnesium components, 56° bevel capacity and included accessories. Our score weighs specs and features against what you're shopping for.
Its main drawback in this comparison is the 10.6 lb weight beside lighter corded alternatives. Pick the Makita 5007Mg if its bevel range and included kit match your work; use our DeWalt DWE575SB comparison if carry weight matters more.
Frequently asked questions
Is the Makita 5007Mg a corded saw?
Yes. The 5007Mg is a corded 7-1/4 in circular saw with a 15 amp motor, so you'll need a suitable power supply and an extension cord rated as its manual requires.
Keep the cord clear of the blade and cutting path throughout the cut.
How deep can the Makita 5007Mg cut?
The 5007Mg has a 2-1/2 in cutting capacity at 90°. That suits framing lumber and panel work within that depth, but check the material thickness and depth setting before each cut, since a bevel cut reduces the available cutting depth.
Does the Makita 5007Mg have a light?
Yes, it has two built-in LED lights that illuminate the line of cut. They help you see the marked path, but they don't steer the saw or replace a clear layout line, stable workpiece support and the handling steps in the manual.
What is the difference between the Makita 5007Mg and 5007F?
The 5007Mg has a 0° to 56° bevel range, while the 5007F's range is 0° to 45°. Both have a 15 amp motor and two cut-line LEDs; their cutting capacities at 90° are 2-1/2 in and 2-3/8 in, respectively.
